Our Ultimate Bromine Granule Pack consists of 18 different products to help keep your hot tub clean and sanitised. Bromine is a good sanitiser for hot tubs as it’s less intense than chlorine and therefore kinder on the skin if you have sensitive skin.
1. Add 2 x Teaspoons of Bromine Granules to your hot tub.
When setting up hot tub from start allow up to 24 hours for granules to dissolve and mix with water for correct water balance reading.
2. Test the water with testing strips to check free bromine levels.
Spa water will require checking with a testing strip daily.
1. Add 2 Teaspoons per 1,000 litres of spa water.
2. Using a bucket, dissolve in warm water and distribute evenly around the pool with the pump operating.
3. Leave for 8 hours then re-test to ensure pH level 7.2 - 7.6.
Add more if required until correct balance is achieved.
1. Using a bucket, add 1 teaspoon of pH Minus per 1 litre of warm water and carefully add the solution to the spa whilst the pumps are turned on.
2. Check water balance level with a testing strip (aim for a pH level of between 7.2 - 7.6) and add more Ph Minus if required.
Algae already within system:
1. Shock dose with 20ml per 1,000 litres of spa water.
Prevention of algae growth:
1. Add 2.5ml per 1,000 litres of spa water each week to help prevent future growth.
1. Using a bucket, add 2 Teaspoons of Chlorine reducer per 5 Liters of warm water. 2 teaspoons will treat 2000 litres of water and reduce the level by 1 mg.
2. Once all the crystals have dissolved add to your hot tub.
3. Wait 1 hour and test water balance with testing strips
Add again if necessary to reach the right level of chlorine/ bromine
Shock dose - Dose approximately 100ml per 1000 litre of spa water
Pool clean be used as part of a daily cleaning routine to help keep water clear and free from dirt if in a frequently used environment.
1 x teaspoon will increase the alkalinity level by 2 ppm in a 1,000 litre spa.
1. Using a bucket, add alkalinity builder to 2 litres of warm water and pour dissolved solution into spa water
2. Run pumps for 5 minutes
3. Wait 1 hour and test again with testing strips
Repeat dose if required until correct level is reached.
1. Add 2 x teaspoons to spa water once per week
2. Run pumps for 5 minutes.
3. Place cover on spa and leave for 1 hour before use.
Apply waterline cleaner once per week.
Shock Dose:
Weekly Usage:
Make sure filters are cleaned once a week whilst using no scale.
Hard water areas or heavy scaling may need more application.
1. Add 250 ml per 1750 litres of water
2. Turn on pumps for 5 minutes to allow even distribution.
3. Turn the power off on the spa amd allow to stand for at least one hour.
4. Drain the hot tub.
5. Clean, refill and reset system.
Regular use of Surface Cleaner will maintain a clean and fragrant spa at all times.
Add 50ml to the foaming area as required.
Regular use of Spa Cover Shine will help maintain a clean and fragrant spa cover
1. Dip one strip into water for 5 seconds with a simple back and forth motion
2. Remove strip and shake to remove excess water
3. Wait 15 seconds, Match pH, free chlorine / bromine, total alkalinity & water hardness to the colour chart.
Complete colour matching within 30 seconds.
Place in your hot tub alone or attach to a floating dispenser
Clean sponge once a week
Need some help or advice? Call 0116 251 3378 or email us at customercare@hottubsuppliers.com
Credit subject to status and affordability. Terms & Conditions Apply. Hot Tub Suppliers Limited, 11 Midland Street Leicester LE1 1TG FRN: [654375] is a credit broker and is Authorised and Regulated by the Financial Conduct Authority. Credit is provided by Novuna Personal Finance, a trading style of Mitsubishi HC Capital UK PLC, authorised and regulated by the Financial Conduct Authority. Financial Services Register no. 704348. The register can be accessed through http://www.fca.org.uk
© HTS 2024. Powered by Webfuel Nottingham